Datacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory) 990

Review for datacomm flat panel tv cable organizer

Price was $39.05. If you want a clean efficient cord organizer, this is the one to buy! outstanding product to get of cords dangling from flat screen tv!

-H. Irene

Datacomm Flat Panel Tv Cable Organizer Kit Power Solution – Our Home Theater Products Provide All The Flexibility Installers Or Experienced Do-it-yourselfers Need To Create Sophisticated Media Environments. Our Plates Mount Into A Standard -Datacomm 50-3323-wh-kit Flat Panel Tv Cable Organizer Kit Power Solution – White

  1. Special: Brings Power To Your Wall Mounted Tv Without The Added Expense Of Installing An Electrical Outlet.
  2. Special: Grounded Recessed Single Receptacle Allows Power To Be Installed Behind Your Wall Mounted Tv Or Other Display.

Reasonable Datacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory) 50 3323 Wh Kit

Buy Now


Introduction

I purchased this product to conceal wires for a planned mount of a 46" lcd flat screen. I have minimal contractor skills but have done some prior successful diy home projects, including installing lighting fixtures, tile, shelving units etc. I was able to install both the television mount and this product within a few hours. Before installing (and even purchasing) i read through most of the reviews and watched the video for the installation of this product a few times. The reviews here are very helpful (read: essential) in addressing a few tips that can make this project run much more smoothly:. . 1. The template is probably the exact size, but it helps to trim it down slightly so that you don't make a hole in the drywall that is too large. I did this and then readjusted the size of the hole so that the cable plates fit perfectly. It was a bit tedious but i wanted to feel confident that the installation would be precise. 2. Either trace the template of the mount with your studs readily identified (as suggested) or go ahead and install the wall mount (before putting the tv on the wall) before tracing the template for the cable plate. You can look at the back of your tv to determine where the hdmi cables insert to give a better idea of where the cable plate should go. You have also essentially identified the studs and wont try to put a drywall knife through one. 3. Flip the bottom plate so that the guided slot for the hdmi cables runs straight down. This means that you will need to wire in the electrical box on the right side for this plate. Planning for this at the time of installation means not having to move it to the right if you do decide to flip the plate. Many people recommended this so that you don't essentially lose length of the cord because its path becomes more tenuous thanks to the awkward slanting slot. 4. Watch the video as you work. You can find it on youtube, or by searching for "datacomm 50-3323-wh-kit". It's much more logical than the weird instructions and the woman's positive attitude is very encouraging :). . I do recommend this product overall, and find it to be an excellent, creative solution to a potential code issue. Best datacomm flat panel tv cable organizer | Datacomm Electronics-Ce Accessory Review ( Mar 2019 ) Special Datacomm 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White Low profile design fits behind the industry's thinnest tvs and mounts. 6 feet extension cord, 8 feet of non-metallic electrical wire. Brings power to your wall mounted tv without the added expense of installing an electrical outlet. Grounded recessed single receptacle allows power to be installed behind your wall mounted tv or other display. Connects your wall mounted tv or other display to your receiver or av components. Cable pass-through ports on the top and bottom plates allow you to run your low voltage av cables from your tv, through the top plate, inside the wall, and out through the bottom plate to connect to av equipment. Mounting wings are molded onto the top and bottom plate and fasten against the drywall as you tighten. No low voltage mounting brackets or mud rings required. All-in-one kit includes everything you need - quick and easy to install .

Datacomm 50-3323-wh-kit flat panel tv cable organizer kit with power solution - white Review (50 3323 wh kit)

Great product overall. . Pros:. Easy to install. Good price $40 for me. Clean look. Good directions, even includes a cut template for the drywall. . Cons:. The color is not a bright white but more "cream". . The kit included two bottom pieces, meaning i had to flip some installed components for proper installation (the openings for the wires were on opposite sides) which was not a major issue but why i gave the product 4 stars. -D. Clara

Datacomm 50 3323 Wh Kit Panel Organizer Solution

  • Order: Electronics
  • Brand: Datacomm Electronics
  • Color: White
  • EAN: 6093845452190
  • Product Dimensions:
    Height:3.75 inches
    Length:5.75 inches
    Weight:2.25 pounds
    Width:4.70 inches
  • LegalDisclaimer: Must Be At Least 18 & Over To Purchase
  • Manufacturer: DataComm Electronics, Inc.
  • Model: 50-3323-WH-KIT
  • MPN: 50-3323-WH-KIT
  • Quantity: 1
  • Part/Serial Number: 50-3323-WH-KIT
  • Sub-Type: Speakers
  • Category: CE ACCESSORY
  • Size: 50-3323-WH-KIT
  • UPC: 617689107632
  • Warranty: 10 Year - Parts Only.

datacomm flat panel tv cable organizer kit power solution - Speakers, Our home theater products provide all the flexibility installers or experienced do-it-yourselfers need to create sophisticated media environments. our plates mount into a standard nema enclosure or on to a low-voltage mounting bracket. straightforward labeling on each plate simplifies room set up and configuration. Datacomm 50 3323 Wh Kit Panel Organizer Solution (50-3323-WH-KIT-Datacomm Electronics).

Datacomm 50 3323 Wh Kit Panel Organizer Solution Speakers

PROS
  • I purchased this item for my new tv that i mounted on the wall. The plug was about 2' away from where the tv was to be mounted and i didn't want to attempt adding a new plug. This kit gives you everything you need excluding basic tools needed for cutting the drywall and hooking up the power. If you know nothing about electrical or basic carpentry i wouldn't attempt alone but if you do then this kit is for you. The opening in the wall plate for running wires is plenty big enough. I have 2 hdmi, component video and audio rca's running through it and probably have room for one or two more cables. . Looks great!
  • After never doing an in-wall installation before, i was just a little intimidated by this kit. But, i was working in my gym and really didn't care about screwing things up, so i went ahead and took the shot. . This kit worked out really well. The instructions were pretty simple, perhaps requiring a bit of assumption to fully comprehend, but i was able to work out what they meant well enough. Note that when it says "designed to be installed between studs, " it means that there are no stud mounting points for the in-wall electrical boxes, so you want to keep a bit of distance between them and the studs. . Based on some reviews, i cut out the provided template just a tad small and really used it just to establish the corners. Wanting things level, i used a large level to draw the final square on the drywall where i wanted the plates to go. Then, i drilled some initial guide holes in the corners and used my drywall saw to cut out the wall. Once i had the holes, i roughed in the plates to check fit and level, and then refined the cut a bit to get everything right. Note, though, that the plates use little "flappers" that tighten against the inside of the wall when you screw the plate in to hold it in place. The top flapper extends just a bit outside of the square when set in the initial vertical direction, so i had to notch the wall a bit on the upper right-hand corner of the square to set the plate on the wall. . Next, i installed the electrical boxes. Easy enough using the same "flapper" hold system as the plate. The instructions are not really explicit that the boxes are for covering up the left-hand side of the plate that holds the power, plate only has screw holes on that side for mounting the plate to the box. The boxes secured to the wall easily. I then checked for plate fit one more time and filed the wall a bit more in the necessary places. Another thing not explicitly stated in the instructions is that you need to punch out holes in the back of the box to allow the wire through. Easy enough to do, but i suggest doing it before you install the box. . When it came to the wiring, it was fairly easy to manage if you have a good wire cutter. The outer sheath is very strong and the wire seems to be good quality. I ran the wire through the wall first with a wire pull rod, put it through the punched out holes of the electrical boxes, and then did the stripping. The instructions were then perfect for matching the wires and wiring up the power sockets. Then, i ran an in-wall rated hdmi cable through the wall and then through the plates. After that, i secured the plates. Everything is tight and level. . A couple of notes that cut a star off of the rating. First, i was disappointed that the low-voltage ports on both plates are pointed in the "down" direction. I would have preferred the lower plate (the one you generally put power to) were pointed in the "up" direction to more easily facilitate future cable runs. You could always flip the plate, but then the power would be upside-down. More cosmetic than anything. Also, the power cable sticks a good bit out of the wall. I would have preferred the end to be a bit smaller to put the bend a little more flush with the plate.
CONS
  • This product is a good enough way to hide your wires inside the wall. I am only giving it 2 stars because my package had parts missing. One of the low voltage wire boxes was missing. I ended up go ng to the hardware store and spending a couple dollars on a replacement box, less time consuming than having to return the product.
  • Cheap screws striped way too easily
  • When received, product was missing an electrical box. There should have been two and one was received. Had to go to hardware store to buy another to be able to complete project as we did not have time to return and get a replacement. Also, this will not work if your tv has a 90 degree power cable.

datacomm flat panel tv cable organizer Datacomm 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White (Switch to Mobile/Desktop Version)

I chose this over the other brand's option because this is a standard 2 gang size and would fit my needs better. All the parts needed are here in one kit so no need to run back and forth to the hardware store. . My rating is four stars because of two things:. 1. Feels like a lot of pressure it needed to plug the extension cord into the bottom plug, but the box did hold. 2. The drywall cut out template is slightly off. *. . *to elaborate, there are two screw wings on the gang box and two screw wings on the wall plate. If cutting exactly to the drywall template, the wings on the box are only holding 1/4 inch of the drywall instead of the full 3/4 inch. And the wall plate wings are out 1/8 inch too far so you'll need to cut a bit extra to get them to fit through the drywall. This is not a huge deal unless you cut way outside of the template. My suggestion would be to cut the drywall a bit smaller than the template so you fit to the gang box and then cut whatever extra you need to fit the wall plate wings in.

Datacomm 50-3323-wh-kit Flat Panel Tv Cable Organizer Kit Power Solution - White
Click to see NoticeDatacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory)"Just installed it - looks great. . I m not super handy especially with electrical so i took my time and followed the directions. I noticed the male end side for hdmi wires appeared upside down and it seemed like template could have been a little smaller and the tabs for the box were annoying but overall at the end of the day it looks better than it did before."

(0) Question: Will the ears on the box grab on double drywalled wall?


(1) Question: Whats the difference between this one and the datacomm 45-0023-wh for $10 less?


(2) Question: The wall im using this on has insulation. will this still be ok to use & not go against any type of nec / fire code? dont want to burn my house down.



Featured Categories » Gold Merchants » Specialty Boutique » Datacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory) 50 3323 Wh Kit


Mounting Dream MD2380 TV Wall Mount Bracket 26-55 Inch LED, LCD, OLED Plasma Flat Screen TV, Full Motion Swivel Articulating Dual Arms, up to VESA 400x400mm 99 LBS Tilting

I was super impressed with this mounting system. Came with everything. And i mean everything to mount it. Surprised they didn't ship a drill with it as well. Has multiple levels, all the screws you could dream of, and surprisingly clear directions. They give you straight forward information about the options for mounting. No wiggle, and takes a little effort to move the tv around which is good so it's not just swinging in the breeze. Really like this mount and will be suggesting them to friends.

Fits 26-55" tvs this mount fits most of 26-55" tvs sold today. It fits tvs with mounting holes as close as 3"x3" or as wide as 16"x16" (in tv terms - vesa 75x75mm to 400x400mm). Specifically, it fits vesa 75x75mm, 100x100mm, 200x100mm, 200x150mm, 200x200mm, 300x200mm, 300x300mm, 400x200mm, 400x300mm, 400x400mm. Retracts 3" low profile, extends 15. 2" from the wall with articulating arm, this mount retracts to 3"(to wall) to save space, and extends up to 15. 2" from the wall. Tilt, swivel and rotate function +5 /-15 tilt, +/-45 swivel and +/-3 rotation for maximum viewing flexibility, provide smooth adjustment for all directions, making it easy to view your tv from multi-angles. Heavy duty steel construction, 99 lbs loading capacity constructed with heavy duty steel materials with durable powder coated finish. This mount is 100% welded by automatic robot. This advanced welding technology makes the mount sturdy, and ensures mounted tv stable and secure, supporting tv weight up to 99 lbs. Bubble level and 6' high speed hdmi cable it comes with bubble level and 6' hdmi cable. Hdmi cable supports 3d, ethernet, 1440p and audio return conforming to latest hdmi 1. 4 standard. Includes all necessary mounting hardware this mount ships with hardware for both wall and tv mounting. Anchor included is only for concrete wall installation not for dry wall alone application! rohs certified this product is rohs certified (european union directive standard of restriction of hazardous substance), aiming to protect human health and environment.

Mounting Dream MD2380 TV Wall Mount Bracket 26-55 Inch LED, LCD, OLED Plasma Flat Screen TV, Full Motion Swivel Articulating Dual Arms, up to VESA 400x400mm 99 LBS TiltingMounting-Dream-Bracket-Articulating-400x400mm

Mounting Dream Bracket Articulating 400x400mm (Av Furniture) FAQ.

Pretty sturdy, but ridged movement when pulling all the way out or pushing back in can be a hassle sometimes if you don't use some finesse (the cost makes it still okay). Pros-. Feels pretty sturdy. Practically any angle if your not hanging it way too high. (doesn't tilt downward too much but still works out great). Very easy and wide left and right (vertical) turn capability. Mostly an easy setup. Cons-. Really big screws can't remember the size, feels like a quarter of my 1. 5 inch studs at the least. (not sure if that's normal for a tv mount). Need and hex key to tilt up or down. Very rigid sometimes when retracting into or extending it away from the wall, can feel awkward if your in front of people haha, unless you use some finesse and slide it left and right when extending or retracting it, it kinda helps usually. Note/con. Need a good drill with right socket size as philips bits don't cut it with these big screws. Overall though for what i paid, and the fact that my 55 inch 4k samsung didn't fall off my wall and that i can get it to any angle i usually like with very little to no effort makes me happy :) thanks guys. -Notice from V. Arnett, Manitoba

Click to Show mounting dream bracket articulating 400x400mm (av furniture) Details

I always wanted to mount a tv on my wall and i did just that with this tv wall mount. Several positives include:. . 1) can move the tv in many angles. . 2) there is a paper included in the box that looks similar to metal frame with holes used on the wall. This made it extremely easy to figure out where to drill holes. . 3) many different types of screws included to mount to the wall. . 4) instructions pretty clear; not too difficult. . That being said, there are certain things to watch out for, including:. . 1) using a stud finder (not included) to find an area to mount the tv. . 2) using a device to make sure the mount is level (not included). . 3) being careful when drilling a hole on the wall. . I highly recommend this tv mount. Beats the $90 mount i purchased from best buy that only moves up and down. I returned that mount the next day.

Mounting-dream-bracket-articulating-400x400mm-(av-furniture) set picture

- . MatherlyThis went up so easily, and in less than an hour, no problems at all! we were leery about the inexpensive price thinking it might be a low quality product, but we were pleasantly surprised and impressed with the quality of this item! when considering this purchase, we had read the majority of reviews. Now, after installing this item ourselves, we are convinced that most of the complaints reviewers had were because they didn't pay attention to the written instructions (or they didn't even read them), and read the labels on the packagings. For example one person complained that his tv wasn't level. Yet in the instructions clearly show the leveling bolts on the frame that should be used.

This is a great, sturdy mechanism. I recently bought a 55" tv and used this to mount on the wall. The back plate only spans 16" o/c studs, but the mounting plate can move severall inches either side of center. There is an additional bracket (sold separately) if your studs are spaced wider or the existing studs don't quite center the tv where you want it. I like the flexibility of the bracket that allows it to lay fairly flat on the wall or pull out and turn several degrees to watch it from another part of the room. I have this in my basement. So this is handy if i'm watch from the couch or using my exercise equipment. This is also very handy if you need to access the rear to change cables or add devices to your tv. Super simple to install, but with any tv mount, make sure you mount it to the wall studs! really, you pay all that money for a tv and hang it on the drywall? smh. Accepts most standard vesa mounting configurations

W. Jennifer, Louisiana

MOUNTING DREAM MD2380 TV WALL MOUNT BRACKET 26-55 INCH LED, LCD, OLED PLASMA FLAT SCREEN TV, FULL MOTION SWIVEL ARTICULATING DUAL ARMS, UP TO VESA 400X400MM 99 LBS TILTING Reviews
Brand :    mounting dream
Color :    16" Wood Stud
Size :    16" Wood stud
Model :    FBA_LYSB00SFSU53G-ELECTRNCS
Quantity :    1
Order click here :    normally ships in 24 hours
Home Theater :    Best Av Furniture (mounting dream product review) for Mounting Dream MD2380 TV Wall Mount Bracket 26-55 Inch LED, LCD, OLED Plasma Flat Screen TV, Full Motion Swivel Articulating Dual Arms, up to VESA 400x400mm 99 LBS Tilting available ( Mar 2019 )
Price :    $27.99 (was $34.99)
  • Us based customer support answers your pre-purchase and installation questions. our mount is 10 year warranted!
  • Heavy duty unit fits for most of 26-55" tvs up to 99 lbs, with max vesa of 400 x 400mm/mounting holes spacing. our mounts are tested with 4 times loading listed. images on left side will help you see if this mount perfectly fits your tv in the aspects: like vesa, 16" studs spacing and possible blocked input. not perfect? you can check other mounting dream mounts for best options.
  • Viewing becomes more comfortable: tilts tv up 5 and down 15 to reduce glare, swivels tv left or right according to your seats position. pull out to 15. 8 and retract back to 3. 6, making your tv alive to move
  • Easy installation with decent instruction and all included hardware in pre-labeled bags. +/-3 post-installation adjustment allows perfect tv leveling. comes with 6 hdmi and torpedo level as gifts.
  • Technology of robot welding makes whole unit sturdy and safe.

VideoSecu Mounts Tilt TV Wall Mount Bracket Most 23 - 75 Samsung, Sony, Vizio, LG, Sharp LCD LED Plasma TV VESA 200x100 400x400 to 600x400mm, Bonus HDMI Cable Bubble Level MF608B BBM

This low-profile tilt mount is designed for most 23-75 inch flat-panel tvs weighing up to 165 lbs. Vesa compliant for simple installation, supports tv with mounting hole patterns up to 23. 6" horizontally, and 16" vertically (vesa 600x400mm). Adjustable 15 degrees forward or backward tilts to provide comfortable viewing when the tv is mounted above eye level or to reduce screen glare. Perfect choice for mount your flat-panel tv on a wall, with stylish appearance, and it makes tv viewing so much better. Open wall plate for electrical access. Fit 16" or 24" studs typical in us homes. Common wall and tv attachment hardware are included in the box. Notice: this mount fits most 23-60" tvs (vesa hole patterns from 200x100 mm (8x4") to 600x400mm (24x16")), some up to 65 70 75 inch tvs manufactured in recent 3 years.

VideoSecu Mounts Tilt TV Wall Mount Bracket Most 23 - 75 Samsung, Sony, Vizio, LG, Sharp LCD LED Plasma TV VESA 200x100 400x400 to 600x400mm, Bonus HDMI Cable Bubble Level MF608B BBMVideoSecu-Bracket-Samsung-600x400mm-MF608B

VIDEOSECU MOUNTS TILT TV WALL MOUNT BRACKET MOST 23 - 75 SAMSUNG, SONY, VIZIO, LG, SHARP LCD LED PLASMA TV VESA 200X100 400X400 TO 600X400MM, BONUS HDMI CABLE BUBBLE LEVEL MF608B BBM Reviews
Brand :    videosecu
Size :    23-75 inch
Model :    MF608B
Quantity :    1
Order click here :    normally ships in 24 hours
  • Low profile display your tv with stylish appearance ; strong and durable dual steel frames
  • 15 degrees forward or backward easy one-touch tilt to reduce glare, easy install
  • Fits 23" to 75" tv with vesa from 200x100 to 600x400 (mounting hole pattern up to 24" horizontal by 16" vertical)
  • Durable construction supports up to 165 lbs; fits up to 24" studs
  • Bonus 6" 3-axis magnetic bubble level, 10 ft hdmi cable and standard hardware included; assembly required
Price :    $20.11 (was $21.99)
Ce :    Best Av Furniture (videosecu product review) for VideoSecu Mounts Tilt TV Wall Mount Bracket Most 23 - 75 Samsung, Sony, Vizio, LG, Sharp LCD LED Plasma TV VESA 200x100 400x400 to 600x400mm, Bonus HDMI Cable Bubble Level MF608B BBM available ( Mar 2019 )

Klein Tools 56005 1/4-Inch Wide Steel Fish Tape, 25-Foot

The klein 56005 depth finder high strength 1/4-inch wide steel fish tape is 25 feet long and features permanent, laser etched 1-feet increments on the tape allow you to more accurately measure the depth of conduit runs and determine the amount of tape left to pay out. The polypropylene case and handle are extremely durable and offer the maximum in shock and impact resistance. Raised finger grips help transfer 100-percent of the winding power from your hand and fingers. The round inner ring design provides a smooth, consistent and comfortable surface for winding and rewinding. The unique sloped handle optimizes the position of your hand for quick hand-over-hand rewinds and allows a more level payout of tape on the backswing while feeding conduit. Tempered, high quality tape keeps its stability as it glides between surfaces for effective pushing and pulling of wire under carpets, through insulated walls and over suspended ceilings. The 25-foot length is perfect for short wire runs associated with light commercial, residential and voice-data-video-audio installations. It also has a no-snag plastic tip. Reel diameter: 7-inch. Tape size: 25-feet l x 1/4-inch w x . 030-inch h. Weight: 1. 1-pound. Warnings: wear approved eye protection when feeding, pulling or rewinding fish tape. Do not use any fish tape on or near live circuits. Use extreme caution when working near any electrical equipment. Use a safe work position to avoid loss of balance when using fish tape. Never remove screws while fish tape is coiled inside reel.

Klein Tools 56005 1/4-Inch Wide Steel Fish Tape, 25-FootKlein-Tools-56005-4-Inch-25-Foot

KLEIN TOOLS 56005 1/4-INCH WIDE STEEL FISH TAPE, 25-FOOT Overview
Brand :    klein tools
Color :    Multi
Size :    25-Feet
Weight :    1.05 pounds
Model :    56005
Quantity :    1
Order click here :    normally ships in 24 hours
Home Improvement :    Best Tools (klein tools product review) for Klein Tools 56005 1/4-Inch Wide Steel Fish Tape, 25-Foot available ( Mar 2019 )
Price :    $11.38 (was $12.24)
  • Permanent, laser etched 1-feet increments on the tape
  • Polypropylene case and handle are extremely durable, offer maximum in shock and impact resistance
  • More accurately measures the depth of conduit runs and determines the amount of tape left to pay out
  • Round inner ring design provides a smooth, consistent and comfortable surface for winding and rewinding
  • Raised finger grips help transfer 100-percent of the winding power from your hand and fingers

Stanley 15-556 Jab Saw Cushion Grip

The stanley 15-556 contractor grade cushion grip wallboard saw features a fully hardened, tempered blade that is designed for long cutting life. The sharp tip makes plunge cuts easy, and the teeth are engineered to cut fast and prevent clogging. It also features an ergonomically designed curved handle which is cushioned for comfort.

Stanley 15-556 Jab Saw Cushion GripStanley-15-556-Jab-Cushion-Grip

STANLEY 15-556 JAB SAW CUSHION GRIP Featured
Price :    $5.90 (was $6.59)
  • Sharp tip makes plunge cuts easy.
  • Ergonomically designed curved handle is cushioned for comfort.
  • Teeth are engineered to cut fast and prevent clogging.
  • Fully hardened, tempered blade is designed for long cutting life.
  • Blade is epoxy-bonded to handle for a secure fit and durability.
Brand :    stanley
Size :    Pack of 1
Weight :    0.57 pounds
Model :    15-556
Quantity :    1
Order click here :    normally ships in 24 hours
Home Improvement :    Best Tools (stanley product review) for Stanley 15-556 Jab Saw Cushion Grip available ( Mar 2019 )

Stanley 20-556 6-Inch FatMax Jab Saw

Stanley jab saw 6-1/4 blade fatmax sharp tooth blade cuts 50% faster than traditional tooth design bi-material handle sharpened tip easily punches through drywall will cut cement board online store. Com the stanley 6-inch fatmax jab saw has a sharpened tip that punches through drywall or other similar materials with ease. Designed for drywall, wood, and plastic work, this versatile saw has a slip-resistant handle that's created for strength and durability, plus precision grip that gives you excellent control. Versatile, durable, and designed to accomplish tasks efficiently. Designed to meet high standards for quality and performance. See the full line of saws. The 20-556 features sharptooth technology so it cuts on the push and pull strokes, which means that it saws through any material up to 50 percent faster than traditional tooth designs. Its blade is hardened and tempered for long life and reliable service, and slip-resistant handle is designed to be tough - even as it helps lend real accuracy to any project you're working on. This saw's blade is six inches long, and it's rugged enough to cut through durorock. About stanley fatmax saws the fatmax family of products has established itself as one of stanley's most extensive and innovative product families in the company's 161-year history. The fatmax line of hand tools features core tools essential for the pro or expert enthusiast who desire high quality, durable tools. The fatmax saw features blades that are 15-percent thicker than conventional saws for straighter cuts with less binding. Stanley's unique sharptooth saw technology uses three cutting surfaces to cut 50 percent faster than conventional hand saws, while induction-hardened teeth stay sharp up to five times longer than standard teeth. The back of the saw can be used to mark the 45 and 90-degree angles. And thick, ergonomically designed grips resist slipping and adds comfort during strenuous jobs.

Stanley 20-556 6-Inch FatMax Jab SawStanley-20-556-6-Inch-FatMax-JabThe stanley 6-inch fatmax jab saw has a sharpened tip that punches through drywall or other similar materials with ease. Designed for drywall, wood, and plastic work, this versatile saw has a slip-resistant handle that's created for strength and durability, plus precision grip that gives you excellent control. Versatile, durable, and designed to accomplish tasks efficiently. Designed to meet high standards for quality and performance. See the full line of saws. The 20-556 features sharptooth technology so it cuts on the push and pull strokes, which means that it saws through any material up to 50 percent faster than traditional tooth designs. Its blade is hardened and tempered for long life and reliable service, and slip-resistant handle is designed to be tough - even as it helps lend real accuracy to any project you're working on. This saw's blade is six inches long, and it's rugged enough to cut through durorock. About stanley fatmax saws the fatmax family of products has established itself as one of stanley's most extensive and innovative product families in the company's 161-year history. The fatmax line of hand tools features core tools essential for the pro or expert enthusiast who desire high quality, durable tools. The fatmax saw features blades that are 15-percent thicker than conventional saws for straighter cuts with less binding. Stanley's unique sharptooth saw technology uses three cutting surfaces to cut 50 percent faster than conventional hand saws, while induction-hardened teeth stay sharp up to five times longer than standard teeth. The back of the saw can be used to mark the 45 and 90-degree angles. And thick, ergonomically designed grips resist slipping and adds comfort during strenuous jobs. Br clear "all"

STANLEY 20-556 6-INCH FATMAX JAB SAW Overview
Price :    $8.65 (was $10.57)
  • 6-inch blade; limited lifetime warranty
  • Thick, ergonomically designed grip resists slipping and adds comfort
  • Sharptooth technology cuts 50% faster than conventional saws
  • Induction-hardened teeth stay sharp up to 5 times longer than standard teeth
  • Sharpened tip for puncturing drywall
Brand :    stanley
Size :    Pack of 1
Weight :    0.1 pounds
Model :    20-556
Quantity :    1
Order click here :    normally ships in 24 hours
Home Improvement :    Best Tools (Home Improvement product review) for Stanley 20-556 6-Inch FatMax Jab Saw available ( Mar 2019 )

Cheetah Mounts APDAM3B Dual Articulating Arm TV Wall Mount Bracket 20-65 TVs up to VESA 400 115lbs, Mounts to Two 16 studs includes a Twisted Veins 10 HDMI Cable a 6 3-Axis Magnetic Bubble Level

Fits 20-65" tv's up to vesa 400 and 115lbs this mount fits virtually all 20-65" tvs sold today with vesa hole patterns from 50x50mm (2x2") to 400x400mm (16x16") and up to 115lbs. 14" extension, low 2. 7" profile, 130 swivel, 10 tilt the articulating arm extends up to 14" from the wall yet collapses to 2. 7". The mount allows for up to 130 swivel and 10 tilt. Allows 3 rotation adjustment to level after installation slots in the tv plate allow for 3 of rotation adjustment to level the display after mounting. Mounts to two 16" wooden studs as well as all masonry the apdam3b can be mounted to two standard 16" wooden studs as well as all types of masonry. All mounting hardware is included. 10' twisted veins hdmi cable and 6" magnetic bubble level the mount includes a 10' twisted veins high speed with ethernet hdmi cable featuring 4k 60hz 3d signal support and a protective braided jacket. A 6" 3-axis magnetic bubble level ensures level mounting. Includes all necessary mounting hardware this mount ships with hardware for both wall and tv mounting. Lifetime 100% guarantee all our mounts come with a lifetime guarantee. If you experience any issues, please contact us.

Cheetah Mounts APDAM3B Dual Articulating Arm TV Wall Mount Bracket 20-65 TVs up to VESA 400 115lbs, Mounts to Two 16 studs includes a Twisted Veins 10 HDMI Cable a 6 3-Axis Magnetic Bubble LevelCheetah-APDAM3B-Articulating-Bracket-Magnetic

CHEETAH MOUNTS APDAM3B DUAL ARTICULATING ARM TV WALL MOUNT BRACKET 20-65 TVS UP TO VESA 400 115LBS, MOUNTS TO TWO 16 STUDS INCLUDES A TWISTED VEINS 10 HDMI CABLE A 6 3-AXIS MAGNETIC BUBBLE LEVEL Advantage
Price :    $33.96
  • Includes a 10' twisted veins hdmi cable, and a 6" 3 axis magnetic bubble level
  • 14" extension yet only 2. 7" when collapsed, 130 swivel and 10 tilt
  • Mounts to 16" wooden studs as well as all masonry
  • Allows for 3 rotation adjustment to level after installation
  • Fits 20-65" tvs with hole patterns up to vesa 400x400mm (16x16") and up to 115lbs
Brand :    cheetah
Color :    Black
Model :    APDAM3B
Quantity :    1
Order click here :    normally ships in 24 hours
Speakers :    Best Consumer Electronics (cheetah product review) for Cheetah Mounts APDAM3B Dual Articulating Arm TV Wall Mount Bracket 20-65 TVs up to VESA 400 115lbs, Mounts to Two 16 studs includes a Twisted Veins 10 HDMI Cable a 6 3-Axis Magnetic Bubble Level available ( Mar 2019 )

Hyde Tools 09016 MaxxGrip Pro Jab Saw

For cutting drywall, wood, masonite, plywood, etc. Sharp point for easy penetration without drilling. High carbon steel blade. For cutting drywall, wood, masonite, plywood, etc. Sharp point for easy penetration without drilling. High carbon steel blade.

Hyde Tools 09016 MaxxGrip Pro Jab SawHyde-Tools-09016-MaxxGrip-Pro

HYDE TOOLS 09016 MAXXGRIP PRO JAB SAW Benefits
Brand :    hyde tools
Color :    N/A
Size :    N/A
Weight :    0.35 pounds
Model :    09016
Quantity :    1
Order click here :    normally ships in 24 hours
  • For cutting drywall, wood, masonite, plywood, etc
  • Sharp point for easy penetration without drilling
  • High carbon steel blade
  • Ergo-engineered soft-grip handle
Price :    $6.82
Home Improvement :    Best Building Material (hyde tools product review) for Hyde Tools 09016 MaxxGrip Pro Jab Saw available ( Mar 2019 )

Basics CL3 Rated In-Wall Installation HDMI Cable - 10 Feet

Online storebasics brings you everyday items at a great value an online store brand.

Basics CL3 Rated In-Wall Installation HDMI Cable - 10 FeetAmazonBasics-Rated-Wall-Installation-Cable

BASICS CL3 RATED IN-WALL INSTALLATION HDMI CABLE - 10 FEET Pros
Brand :    basics
Color :    Black
Size :    10 Feet
Weight :    0.34 pounds
Model :    HL-007317
Quantity :    1
Order click here :    normally ships in 24 hours
  • Meets the latest hdmi standards (4k video at 60 hz, 2160p, 48 bit/px color depth) that supports bandwidth up to 18gbps and backwards compatible with earlier versions
  • Cable length: 10 feet (3 meters); backed by basics lifetime warranty
  • Cable allows you to share an internet connection among multiple devices without the need for a separate ethernet cable
  • Cl3 rated for in-wall installations; made with low-smoke materials to resist fire
  • Connects blu-ray players, fire tv, apple tv, ps4, ps3, xbox one, xbox 360, computers and other hdmi-enabled devices to tvs, displays, a/v receivers and more
Price :    $7.49
Speakers :    Best Cable Or Adapter (basics product review) for Basics CL3 Rated In-Wall Installation HDMI Cable - 10 Feet available ( Mar 2019 )

datacomm 50-3323-wh-kit flat panel tv cable organizer kit with power solution - white Price : 39, was : 0 as 2018-01-12
USUKDEFRESITJPCNCAGlobal
United States
Great Britain
German
France
Spain
Italy
Japan
China
Canada
World Wide
Datacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory) Reviewed by on puqus.com

Top datacomm 50 3323 wh kit panel organizer solution (ce accessory) Content

The F.A.Q. for datacomm 50-3323-wh-kit flat panel tv cable organizer kit with power solution - white

This was a very nice setup to hide the cables behind my new tv. It was easy to install and had everything needed besides basic tools for installation.

A number of questions have been asked here.

Showing 20 Q&A on Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution

(0) Question: Is this ul certified?


(1) Question: Are is the exact depth of the kit. i'm installing on an outside wall. thanks.


(2) Question: When installing, can a use a power tri-tap to power both my tv and soundbar?


(3) Question: How long is the actual power cable and does anyone know if there is optional lengths available upon request?


(4) Question: Can i use a power splitter so that i can plug in multiple devices?


(5) Question: Any idea how many hdmi cables can fit through the opening?


(6) Question: Will this item work with 3 inch studs (non weight bearing walls) or will this only work with 4 inch studded walls?


(7) Question: I have a 90 degree plug on my tv's power cord, will this leave enough room for this type of connection?


(8) Question: Should this cable be stripped when putting on wire connectors. directions say not to cut inner sheathing on wires. help


(9) Question: Can anyone provide the dimensions of the faceplate itself? not looking for the cutout size, just want to confirm the outer dimensions of the faceplate


(10) Question: Did this come with the romex cable? it shows it in the pic but i wanted to make sure as someone else said it didn't?


(11) Question: I have a cmu wall with furring and gypsum board which means a smaller cavity. does this work in a shallow wall? or do i need a ful 2x4/6 wall?


(12) Question: Can i use romex instead of the power cable supplied? i need about 10'.


(13) Question: What is the exact depth of the kit. ? installing in the den an outside wall. drywall with 3. 5" of space before i hit concrete.


(14) Question: I read somewhere that this may not work with the newer samsung leds that have a flat power cord because of the recessed plug. is this true?


(15) Question: My drywall is 4 inch deep and maybe a little tiny bit more will this work can i put this in there


(16) Question: Does this have or support a 20amp outlet and 12/2 wiring? i need to run and use 20amp and the right wire for this unit.



(note) Question: where/how to get Datacomm Electronics (manufacturer's brand) accessories & similiar Datacomm Electronics's products

Click to Show/Hide the Answer
Answer:

Click on the marked text to copy to Clipboard

Great solution for inside the wall wiring. I did not need to use the bottom piece and connected the cable directly to the existing wall outlet. It is safer to use the included bottom piece and extension if you never installed or changed a hot-wired outlet. Cable is high quality and about 6 feet long.


Accessories & Supplies 704182, Audio & Video Accessories 235271, Cables & Interconnects 045271, Electronics 282271, Power Cables 062795Top Datacomm 50 3323 Wh Kit Panel Organizer Solution (Ce Accessory) FAQ Content

Best datacomm 50 3323 wh kit panel organizer solution (ce accessory) in review

This makes it very easy to hang your tv on the wall and hide all of the cables. This kit comes with a paper template that you can use to cut the perfect sized hole in the wall for the top and bottom areas so you can mount this thing with ease. Then, all you have to do is wire up the electrical connection and then fish the wires through. I took this one step further and put a small piece of conduit in the wall between these boxes to make the fishing of the cable that much easier.

B. Valencia, Oregon

You might like to see Protective Cover Kindle Voyage, Slate Better Together Slim, Form-fitting Covers Designed By Online Store To Perfectly Fit Your Kindle Voyage And Provide Full Front And Back Protection. The Cover Secures Magnetically, Making -Protective Cover Kindle Voyage, Slate Grey
  1. Details: Innovative Built-in Origami Stand Folds Into Portrait Orientation For Hands-free Reading.
  2. Details: Durable Exterior Protects Your Kindle Voyage, While The Microfiber Interior Protects Your Screen.
Shopping Protective Cover Kindle Voyage, Slate Grey (Book Reader Accessory) Uz516t Protective Cover Kindle Voyage, Slate Grey (53
Or you might like to consider 110 Hd Motorized 16:9 Projector Screen W/ Remote Transform Your Lounge Into A Home Cinema In A Matter Of Seconds - Kick Back, Put Your Feet Up And Lower Your 110" Projector Screen To Enjoy The Full Screen Experience In The Comfort -Homegear 110 Hd Motorized 16:9 Projector Screen W/ Remote Control
  1. Bonus: High Contrast 1. 3 Gain Screen That Is Washable With Soap And Water, 1" Black Masking Borders To Enhance Picture Contrast, 160 Viewing Angle Perfect For Residential Or Commercial Use, 3 Layer Black Backed Screen Which Eliminates Light Penetration And Produces Top Quality Color Reproduction, Static Resistant, Fire Retardant, Mildew Resistant.
  2. Bonus: Casing & Installation, Durable Steel Casing With Plastic Ends- White, Wall Or Ceiling Assembly, Simple Plug And Play System.
Discount Homegear 110 Hd Motorized 16:9 Projector Screen W/ Remote Control (Office Products) Lysb00j22tm7y Electrncs Homegear 110 Hd Motorized 16:9 Projector Screen W/ Remote Control (Office

Y. Patricia, Virginia says

It does exactly what it says. All the needed parts are there. The price is a little steep for what the product is but hey it works. Do not use the included "template" it is too large. If you cut it back in length and width by 3/16 to 1/4" it would fit much better. You can always cut more out but you cant put it back if you make the hole too big. . What would make this a home run is if they included a 10' hdmi cable.

X. Angela, Mecklenburg-Vorpommern

This is a great way to run power to your tv if there is not an outlet close to piggyback from. My closest outlet was 6 feet away on the adjacent wall. If i were to install an outlet i would have had a ton of drywall repair to do, this saved me a lot of work. It hid my cables leaving a nice sharp look. It maybe took 20 minutes to install. I'm pretty handy, but even a novice could install this rather easily. Very happy with it. I highly recommend this product.

V. Emily, Limousin says

I bought this to install to a friends new apartment after mounting their 47" tv to the wall. They didn't want to see any cords on the outside, and i didn't want to be responsible for their apartment burning down because they ran the standard power cable through the wall. . So, i did some research, and compared this product to the "power bridge" brand. I chose datacomm because it was slightly cheaper, still had great reviews, and included the additional wiring "chute" next to the power receptacle. The powerbridge model has an odd horizontal rotation as well, which i wasn't overly fond of either. . Once the box came in, i was pleasantly suprised to find all the parts i would need to complete the job. Make note, you'll need a phillips and flat-head screw driver, wire cutters/strippers, and a drywall knife for best results. The box includes a tempalte to cut out, two plastic wiring boxes, a liberal amount of romex-brand in-wall copper wiring, the external wall plates with receptacle, and of course all the screws you'll need to tighten everything down. . Install is really easy if you've ever cut a hole in drywall or installed a basic electrical outlet. Even if you haven't, the process is pretty basic in any case. It took me about 30 minutes from start to finish to make it look perfect. . Couldn't be happier with the purchase!

. Lewis, District of Columbia

This product met all my requirements in order to hide the wires for a 47 inch tv mounted on the wall of my bedroom. Of course it requires some level of handyman skills and i would not recommend it as a diy project for someone who has never attempted this sort of thing or who has limited mechanical knowledge or skills. The plastic boxes look good and work well as long as you're careful in tightening down the included wings that open up inside the wall to secure the electrical boxes. If you overtighten these, you'll end up with an unusable kit. Other parts are substantial and i am satisfied with my purchase. It's a great solution to calling in an electrician to install a hardwired outlet at three to four times the price. . I would highly recommend watching the installation video found on youtube as well as reading some of the other reviews in order to be fully prepared for the installation. Since you will be cutting your sheetrock, it is much easier to cut it perfectly to begin with than to have to make repairs for incorrectly positioned cuts. . And finally, i extremely highly recommend that you probe behind the wall between the two points where you want to install the kit to ensure that there is not a horizontal fireblock installed between the wall stud because if so, there will be "lots" more work involved to drill a hole through the fireblock to fish the wires through which also means sheetrock repairs and painting will be required. If that's the case, i'd suggest you purchase a surface mount plastic channel system that just screws to the wall and provides a method to hide the wires, albiet the channel will be visible but much neater in appearance than a gaggle of exposed cables running down to the floor.

L. Anonymous, Wyoming says

My wife was on constantly telling me how ugly the cables and wire were going from the tv to the cabinet. I finally decided to hide everything behind the wall. This kit did the trick. It is easy to install with minimal tools (all your really need is a saw to cut out the drywall and screwdriver. Installation took me about 30 minutes and i was able to easily hide my sound cable and hdmi cables behind the wall. The power plug is recessed so if you have a tv mount that is very close to the wall, you still should be able to use this kit. Good value.

. Rita, New York

This was a great purchase. The kits i saw in store were $100 and up and i paid almost half for this one. Install was very easy. You need to make sure that you have space between studs with no cross stud. It comes with a paper template and you can use a dry wall saw to cut open the squares. I recommend installing the power cord and recepitlcle boxes first, then run the low voltage wires liek hdmi or audio cables through the large hole before fixing the recepticles to the wall or putting the face plate on. This allows you to stick your hole hand into the large hole to fish out the cables. . You need some basic electrical tools like wire strippers to connect the two recepticles. If you have ever replaced an ourlet or light switch this is a cinch. Although i worked very slow to make sure i did not make any mistakes, you could do the install in 1-1. 5 hours. You basically cut out to square holes using the templates and a dry wall saw. The recepticle boxes have clamps that you can tighten into the wall with a screwdriver (no need to attach the box to a stud). You connect the two power recpticles with a ul certified wire (provided, but you need to cut and strip the wire jackets). You then run the low voltage av cables, slap on the face plates and you are done. . I will be buying another one to mount a tv in the bedroom next.

T. Denise, Norfolk says

This is my first datacomm product, but i am highly impressed. At first i was going to buy the single gang low voltage plates for audio/video and then run the electrical myself. But, fortunately i discovered this kit here on online store. It sure looked like it would make my install/life much easier, and it did just that. . I love the look of our samsung un60d7000 60" led display hanging on the wall with no cables in sight. . I did run into one minor issue, that got resolved easily. The extension cord that comes with the kit has a straight female end that attaches to the lower plate. This sticks out a fair amount. I wanted the option of being able to move our bush furniture sonoma large tv stand, mocha cherry veneer (media cabinet) closer to the wall. I searched and pondered, but couldn't find a ready solution. . So, i contacted datacomm's customer support by email. . Kristin d. Was quick to reply. At first she could only state that is the way the kit is manufactured. I asked if it were possible to get another top plate to put in place of the bottom plate. That way, i could build up a right angle cable using a nema male plug on one end. This would plug into the recessed plate just like the right angle plug from the tv did into the recessed top plate. . Btw, i could have searched for the parts needed to build my cable locally, but instead i found exactly what i needed here on online store: whirlpool w10278923rp 3-prong dishwasher power supply kit and leviton 000-515pr-000 15 amp black rubber plug grounded 125 volt. Easy! . . Anyway, i fully expected kristin to direct me to a point of purchase, if the plate was available separately. Instead, she asked for my mailing address so she could ship a new plate free of charge. Thanks, kristin/datacomm! . . The plate arrived within a few days, i installed it as planned and gained 2" more clearance! our media cabinet is only 1 1/4" from the wall now. Better for hiding the mass of cabling behind it. . I noticed a few negative reviews here before placing my initial order. Based on my experience with customer service, i would highly recommend purchasing this product.

M. Kelly, Richmond upon Thames

Works great and was really easy and quick to install! i used it in my home office to hide the cables on my tv i use as an extra monitor for meetings. It makes the tv look sleek and professional. The extension cord for giving it power is really long and overkill for my needs. I found a 1' extension cable on online store to replace it.

P. Rebecca, Florida says

I have very minimum skills when it comes to messing with electricity. Simply put, if i mess with it, i get popped. However, with a little help from a you tube video, i was able to get this kit installed fairly easily. Of course, it is not as easy as the video makes it out to be. Fighting your insulation to get your wires through, for example, can be a bit on the aggravating side. I suggest you get much longer cables than you think you need. I ended up with 12' hdmi and rca cables and a 15' ethernet cable to do the job. Also, keep a wire hanger handy. I straightened it out and ran it first, then hooked the cables on to it to pull them through. Made the process easier. . Also, i got my cables at walmart. Do not fall for the best buys crap and buy a $80+ hdmi cable. They are ridiculous. I got all my cables, plus a monster energy drink, for $30 less than just the hdmi cable. Or see if good ole online store has them and have it all shipped at the same time. My picture with the cheap hdmi cable is just as clear, i assure you. . Shipping was fast, got here two days earlier than they said it would. I would recommend this product for a very professional, clean installed look.

. Miller, Hartlepool

In the past, i would drill two inch holes at the tv mount, and just above the power outlet. Now, i can install a professional routing system into my new house.

. Angelica, East Riding of Yorkshire says

We decided to try this kit after i watched the youtube video showing how to install. We were frustruated that we couldn't find any store near us that carried this product. Why do stores not carry this product? it is by far the best on the market. We purchased kits from lowes, home depot and best buy. While the other kits were similar, they were very cumbersome to work with. We decided to return the other products and order this kit online and wait for it to arrive to finish our project. Our project: mount the tv over the fireplace and hide all the cords and channel everything to the bookcase beside the fireplace. I am so pleased with how it all turned out. Don't be afraid to try this even if your project isn't as straightforward as the video shows. We had to create a channel going at a diagonal to the bookcase and were able to make this work great for us.

E. Jarvis, South Australia says

This is a clever way of putting wires into the wall. I would have given it 5 stars, but the provided electrical wire was not as high quality as i wanted. Ended up just using my own for running in the wall. Otherwise, smooth, easy installation. Would buy another if i have another project.

F. Guest, South Tyneside

Works as intended, but what a royal pita to put together. Cant blame the company though, its more my house. . 4 stars only because i snapped off almost all of the clips that were supposed to mount the plates to the drywall. If you've got more than maybe an inch to clear, you're going to have to get handy. I read another review that mention using picture hanging clips, which ended up working perfectly. . Would i do this again? never in a million years. I'd hire an electrician and get one put it in thats up-to-code.

U. Parker, New York says

My electrician installed this and was very impressed with how easy it was and the end result is a very clean look that makes any other installation with dangling wires look like a joke. A must have!

I. Eleanor, Delaware

Brilliant! works better than expected. Easy to install. Over all took less than 30 minutes. Hardest part was removing the tv's, as they have been up for a few months. Well worth the price

R. April, Virginia says

This is our first time trying this type of diy deal. Overall, it took a few hours + 1 trip to home depot. There is an installation video tutorial for this exact model. It's on youtube, google it and watch the video first. . 1. When you follow the cutout make sure you go with the size they gave you. We thought to be safe and cut a little inside the cutout line we traced. No go. We ended up wasting extra time trimming/shaving the cutout to get the face plate to fit. . 2. We had insulation behind our wall plus some sort of barrier running horizontally midway between the top cutout to the bottom (3 ft below). It took much effort to try to even get 1 wire down. That's where the home depot trip came in. Went there in search of flexible tubing about 3" in diameter. Ended up getting a blue tube used for pools for about $11. What we did was cut to the length we wanted and left a little extra slack. Cut out about a 2" rectangular opening (facing out) at each end of the tube (leaving the back of the tube to protect/feed the wires running a little above and below the plates (behind the wall)). That seemed to work perfect. Currently, we have 3 hdmis and and optical audio wire running thru. . 3. For the bottom plate, we ended up facing it upside down. It made it much easier for the wires to slide thru than to wrap them under then up up. So for the 3 prong outlet, the 3rd prong is above the double prongs. Docked 1 star for that. :). . Overall, this is a doable project for novices and it works as advertised. It looks clean and we didn't have to mess with electrical wires, etc.

S. Peggy, Maryland

Just installed this , great instructions , good quality, look fantastic . I used 10 foot cables (hdmi and fiber) to my devices. Works great!

N. Widmer, Redbridge says

This was great for the install of my motorized projector screen. Very easy to install and works great. If i have any complaint, it's that the in wall power wire was only 9' long. In my install with 9' ceilings it was close to being too short but since it does have the extension cord, it made it ideal for plugging it into my power center instead of directly into the wall outlet.

A. Wimbish, Provence-Alpes-Cote dAzur

Man this was really easy to install and it had very good instructions. I did not have a problem with snapping the tabs. Idk maybe i just got lucky. Looks like a pro installed it. Wiring is straight forward. If you are vaguely familiar with house wiring or have ever installed a ceiling fan this is simple. Make sure your hdmi cables are long enough. You may have to take the bottom box out of the wall to see the wires but fishing down a straight wall is pretty simple. Worst case, get some fish tape and call it good.

. Paula, Michigan says

I bought this kit several weeks ago, but after it sat for most of those weeks with my dvds i figured out that it was not going to install itself so when my wife had safely left the house i gathered the kit along with all the cables i thought i would ever need to connect to my tv. If there was a connector on the tv i connected a cable to it. Then i gathered the tools, a drywall saw, wire cutters, strippers, needle nose, 2 and 1 philips screw drivers, level, pen, nylon pulling cord, scissors and the supplied template. . I connected and tested every single cable that i was going to run through the wall, i really did not want to have to go back and replace cables later. With the cables tested i removed the tv to a safe location and began marking the wall with the supplied template that i cut out with the scissors leveling the template before marking the wall. With the holes cut i installed and wired the upper plate with receptacle first and trimmed the supplied the provided piece of romex to length and left it sticking out of the lower hole. Next i ran the nylon pulling cord between the upper plate and the lower hole and began feeding the cables between the two holes. Most of the cables fed easily, but some needed to be pulled with the pulling cord, i had tied the pulling cord in a loop so that every time i pulled a cable through with it all i had to do was untie the cable from the cord and reset the cord for the next pull. Once all the cables were pulled i fed them through the lower plate, wired up the plug and as others have recommended i installed the lower plug panel "upside down" and as others have said, this will make more sense when you have the parts in your hands. When i finished the job i untied the draw string and tucked it away in the nest of cables so that if i change televisions or need to swap a cable the cord is there but like the other cables out of sight. . In the end the entire job took me about an hour including the trip to the store for a second hdmi cable when i started and cleanup at the end. . I have to say that the wall looks a whole lot better without the cords and cables running down it, this was well worth the money and time. . One final tip, you might think about reaching for the drill to tighten the boxes and plates to the wall, i recommend against that because you will ruin the wall if you use a drill to tighten the screws.

. Lara, Kingston upon Thames

This only works against drywall. It is not a stud mounting outlet. Makes it easy to install but very difficult to get stay perfectly level imo. The low voltage opening are great for most cords such as hdmi ect, but was difficult to fit samsung's all-in-one receiver cord through which in my case was the only one i needed. I did get it through, but had to uninstall and reinstall the plates to do it.

G. Brendon, Poitou-Charentes says

It works good just take you time its plastic and plastic breaks. I didn't have any trouble installing it.

C. Hannah, Southampton

This kit is awesome. I have bought 6 of these so far. I like that i can plug my tv into a surge protector and have it protected.

O. Marguerite, Merton says

Since we were having several rooms painted i figured it was the perfect time to replace the sylvania tube tv, that we bought in 1984, in our bedroom. I had that tv mounted up high on the wall in an older tv wall mount and had always been disappointed in the cables running down the wall. This datacomm kit looked like the perfect solution and it is. Installation is fairly straightforward (watch the videos on youtube) but did take me about twice the time i had expected. A drywall hand saw is cheap and sufficient to make the cuts in the wall. . The suggestion i would make is to install the upper cable plate upside-down. (if you're a perfectionist, this means you have to plan ahead and make the upper hole in the drywall offset a little bit from the lower hole. ) the reason for this is to prevent your a/v cable(s) from falling back down into the wall. The cable holes are wide open in the cable plates and it would be very easy for the cable to slip down through the top one which would mean taking the entire thing back apart to retrieve the cable. Installing the upper plate upside-down means the cables have to snake through the opening. This introduces some friction on the cable and hopefully means it won't fall back into the wall when you let go of it before plugging it into your tv.



Top datacomm flat panel tv cable organizer Review

Disadvantage and Critical reviews

. Irene, Thueringen says

The cutout template they provide is a little too big for the electrical boxes. It made it quite difficult to install. But it's in now and a little loose

Y. Garner, North Carolina

The good: romex already stripped, the bad, as others have stated the dog ears which keep the plate snug against the wall board are flimsy. I was careful not to tighten too hard yet with only slight resistance, both boxes have one ear broken each. Not worth returning because i already have their romex in the wall, but the plates are not secure.

Z. Benton, Mecklenburg-Vorpommern says

I have used multiple kits similar to this from several companies. This version is ok - the wiring behind the wall isn't bad however it is not as easy to hook up as some others (not just plug and go). Also, there isn't any sort of cover between the opening where you run additional wiring such as your hdmi and the interior of the wall itself. I would like to have seen some kind of cover instead of just an opening into the wall. On the plus side - directions are easy to follow/use and the plates themselves do not use up much space.

. Campbell, Alberta

This product offers a clever solution for hiding your wires yet keeping code compliant. The package shipped quickly and arrived well packaged. It took about an hour to install, but mostly because i had to figure certain things out that weren't clearly explained and a couple of work arounds to issues, standard fare for a do it yourselfer. . Pros of this product are that it has all parts required minus the tools. Everything from wiring, screws, crimps, etc. Were all included and neatly packaged. All you need is a screw driver, pliers and a straight blade/box cutter to cut the drywall. Also, i like how it is recessed and allows for a clean look even when the tv is off the wall, and the color and shape make it look like it was an original outlet already there. Some of the other brands are shaped oddly or in black and therefore, the outlet clearly looks out of place. Additionally, some of the other popular choices stick out more and are less recessed. The final product looked clean and did what it said it would, it ran the wires through the wall and kept it to code. . Unfortunately, despite doing what it said it would, there are still some cons. First, the directions are horrible. In order to save on paper, they made it wordy with few pictures. The few pictures they did have were confusing and only one of the three served any purpose. These instructions were not for a beginner "do-it-yourselfer" to follow step by step without any confusion. I've done simple wiring for home repairs before and even with that, this was not that clear. Luckily, i had a general understanding of how this product worked already as well as how to run the wiring, but even i became almost discouraged. Also, the box fastening tool isn't very secure as they are essentially loose flaps that screw tight and hold the box tight to the drywall. Even at its tightest, there was some give. There are also some companies that make a similar kit but make everything horizontal in alignment for the top part behind the tv. I now see why. Most people put the outlet in the middle of the tv mount bracket on the wall as most have a square cut out in the middle specifically for this purpose. This square design of this kit's outlet didn't fit so it wasn't completely flush, some of it overlapped metal. A horizontal alignment here would allowed for a lot more flexibility with different kits. Finally, although a minor problem, the extension chord for the bottom part of the kit sticks out too far at the plug going into the recessed socket, making for about an inch sticking out beyond the wall that the entertainment console can't go closer to. It is odd that they would think about recessed plugs but not factor this in with the extension chord they supply. This is a quick fix by purchasing another one, but then that somewhat defeats the purpose of an all-in-one kit. . At the end of the day, the kit did what it claimed it would. However, factoring in all the pros and cons, and then weighing that against the price, i can't really give this product a high score. It did what it said, it hid the wires and allowed for recessed plugs, all while keeping compliant. However, the price wasn't cheap for the kit (i expected more for the price) and purchased separately, you could possibly make this kit cheaper. Additionally, there are other kits that offer the same end result, some with better prices. The directions were bad and there were some design flaws. Were the price to be more competitive, i would have given this four stars, but considering i had to figure out how to put this together myself since the instructions were so poor and unclear, i couldn't rank it any higher. I would most likely try another kit for future efforts.

F. Pamela, Illinois says

One of them arrived backwards. It interferes with our cable with dish so we couldn't use the outlet for our cable box. Which was the whole point.

C. Angelica, Texas

Didn't realize the tv power cord i had did not have a regular plug. It just had a pin plug so was not able to have the product work. Improvised.

U. Kristen, Rhone-Alpes says

My first order came with two identical sockets. They shipped a replacement quickly, however the socket for the plug is upside down. I have ordered this model before and it was pretty smooth transaction and installation.

Q. Sandra, Michigan

I'm a little dumbfounded by all of the glowing reviews. My take is this is a poorly designed and cheaply constructed product, causing unneeded installation difficulties. All in all i found the product finicky, and i found a similar product that was better designed at my local electronics retailer, which i used for a second tv install. There are two issues with this design. First, the electrical box side and the cable housing/plate cover are separate units. Installing these into the hole in the wall, fastening them and aligning them accurately is near impossible. The second issue, which necessitates the separate plastic electrical box, is the use of screw-wired electrical fittings. This is cheap and unnecessary. I have a different but similar system from another maker which uses a better design. The electrical fitting is simply an extension cord on the rear of the upper and lower boxes that plugs into standard fittings. The electrical and video cable sides of the box are a single molded plastic unit, which is very solid. It mounts into my wall securely, as opposed to this device, the two sides of which i couldn't align and is loose. I can't see it because it's behind my tv and a cabinet. Also the outside cover plate is too small, leaving exposed the edges of the cut plaster, though i was careful in cutting my holes to match the template. I wouldn't use it again. I cannot recommend it.

. Finch, Mississippi says

The template i cut the hole with was a perfect fit except the cheap wings. I actually rendered one screw and flap useless trying to cram it in the hole. The template should allow for the wings to go in but you have to cut notches for that. The electric boxes were so cheaply made i almost bought new ones from (big box)but that would have been an hour drive so i made do. Also on the electric, would have been handy to have the electrical wire prestripped and shallow single gang boxes would also have been better

V. Clara, Washington

Great idea and design except the lower power cord does not allow furniture to be flush against the wall.

H. Elanor, Alaska says

Worked just as expected but i had to make some modifications. I had to remove and invert the outlets to make the openings for the wires make sense. It would also have been nice to have the openings for the wires on the same side of the wall plates to make it a straight shot. I had to offset them to do that.

E. Cortney, South Gloucestershire

I was not able to use it because i couldn't find a hollow place in our sheetrock behind our new 75" led tv in which to place the 2 face plates. I used an external plastic conduit i got on online store for the wires that worked fine. A lot simpler solution and code compliant. Another solution is a joto cord sleeve with a zipper.

W. Donna, South Carolina says

Not the easiest to hook up. You have to do a small amount of wiring.

N. Judith, Wigan

Sent me two male plugs, and i had to run to home depot to get the other female one. No big deal, but i didn't want to wait for the return process. Other than that, it worked great.

X. Jackson, Michigan says

When i got these units it seemed like it was a wonderful idea. However, they're not build well.

A. Claudia, Nebraska

No template provided, ended up with a larger drywall hole than needed :/ the product itself is nice, just wish i had a template for a clean drywall cut.

K. Meredith, Midi-Pyrenees says

Its ok. i like the arlington unit better.

D. Whiteman, Calderdale

I've installed a couple sets of these and both times have ended up with loose fitting units. It seems the plastic flaps (for lack of the proper term) that holds the unit from the back side of the sheet rock either shears or bends. Be very careful not to overtighten because this is a very weak point of the unit. . The other issue is when you have a tv cord that has a right angle wall plug. You must go and buy an adapter that will allow you to extend the right angle plug into the deep socket on the product. Would be nice if they included one for you. . Other than these issues, they do exactly what you need them to do and perform well.

P. Hakala, Maine says

Having done considerable electrical work, this is a great idea but, it's low quality and poorly designed. It needs more wall anchoring, that is to say it doesn't hold well in the wall cavity. I think there should be a steel or hard plastic frame to be inside the wall to screw to.

S. Cindy, Brandenburg

Dont waste your money. Great concept but you can go down to home depot or lowes and make the same thing for almost half the price and it will be 2 times the quality. Single outlet which is cheap as can be. I actually had to flip it over since it was installed upside down for my needs. The cord was labeled with cute little stickers so that would help those using it with no wiring knowledge. ( use youtube if you dont know how to hook up a plug or hire a pro). And the plate is a pain to size up for the wall. Save your money and build your own. . I am a professional installer. I decided to give it a shot to see if it would save me time and tried it out on my home first, big mistake as now im going to have to keep it in there since id have to patch the wall to make it smaller. I priced out doing my own setup similar to this from hd and it was about 25 bucks. That also gives you 2 outlets and also i use a 1 gang low voltage box for the wires that has the little brush screen which is a much cleaner look and keep the wall fairly sealed up looking. I will upload picks later but i would no recommend this product for anyone who wants a clean look. . Hope this help those to are looking to do something like this. Also that 25 bucks from hd gets you a good way to getting other tvs done too since you will have left over supplies. You can most likly get about 3 or 4 tvs done for the cost of this.

. Alma, Texas says

It shipped with one electric box missing had to go buy another box at the hard ware store but everything else was ok.

R. Kellie, Derby

Constuction of product where tabs grab sheetrock very fragile on cover plus electrical box which came with the product tabs are fragile too. Extension cord ok along with wire which is 14/2 with ground. Template which came with instructions is too large for cut out in wall. You need to make your hole smaller or it will be way too large for your cover plate etc. If you use the template make sure to cut your hole smaller.

. Tracey, Durham says

Overall this was average. I would have far preferred that the female end not have hard soldered wires, rather screws and/or pressure clips for the romax. Having to use pig tails seems a bit silly. I don't think i would order this again, rather just get standard (and separate) boxes for power and other cabling.

O. Palmer, Missouri

Seal clearly broken on box, purchased "new", missing wire nuts and pair of white screws essential to sealing the white electrical outlet cover to grey electrical box. Buyer beware

L. Joanna, Halton says

Looks nice but if you do not have exact standard studs this will not work for you. Also the electric boxes that come with are not stable so you will have to work around that to install.

T. Patricia, Massachusetts

The neutral broke within minutes of being installed. Cheaply made.

B. Mays, Surrey says

It is a good solution to hiding a/v and power wires. Biggest concern is the electrical wire supplied (for inside the wall to connect the two plates) is only 14-gauge. I'm not an electrician but i was always told that outlets were supposed to be 12-gauge. 14 may be a little thin. Luckily for me i had some 12-gauge laying around. Also, it would be great if it had the option to switch the outlet and the hole for the cables around. Not too big of a deal, but would like to have that option. Other than that, it works.

I. Carmen, Enfield

This product works as intended, the only issue i had with this product is the fact the plastic legs that hold it onto the wall break extremely easily when tightening it. I ended up having to use other methods to get these onto the wall afterwards. Be careful when tightening to the wall. Otherwise for the price this is a great solution for being to code.



Leave a Reply

You must be logged in to post a comment.


Back to Top

Related Products

  • Free Shipping
    Comeap Express Adapter Graphics 24 Inch (4332701845)

    Comeap Express Adapter Graphics 24 Inch (4332701845) 2985

    Purchase Now Comeap Express Adapter Graphics 24 Inch (4332701845), 6 Pin Male To Dual 2 X 8 Pin 6+2 Male Pci Express Power Adapter Cable Graphics Video Card 24-inch Features: The Comeap 6 Pin Male To Dual 2x 8 Pin (6+2) Male Cable Is To Provide A Convenient Solution For Adding Two Extra Pci Express Connectors To Your Existing Power Supply; Specification: -Comeap 6 Pin Male To Dual 2 X 8 Pin 6+2 Male Pci Express Power Adapter Cable Graphics Video Card 24-inch 62cm
    1. Featured: Compatible With 6-pin & 8-pin Graphics Cards From Popular Manufacturers From Asus, Asrock, And Gigabyte;.
    2. Featured: Note: Only Compatible With Coolermaster And Thermaltake Power Supply With 6 Pin Port;.
    3. It's a cable and it works. not much to say. https://puqus.com/comeap-express-adapter-graphics-24-inch-298576yxs6kl/#comeap-express-adapter-graphics-24-inch
    Reasonable Comeap Express Adapter Graphics 24 Inch (Cable Or Adapter)
  • Free Shipping
    Mission Cables Usb Power Cable Fire Tv Stick Fire Tv Included (mc9g)

    Mission Cables Usb Power Cable Fire Tv Stick Fire Tv Included (mc9g) 814

    Show Details Mission Cables Usb Power Cable Fire Tv Stick Fire Tv Included (mc9g), Usb Power Cable Fire Tv Stick Fire Tv Mission Power Usb Cable Allows You To Power Your Fire Tv Stick Directly From Your Tv's Usb Port. It's The Quickest And Simplest Way To Set Up Your Fire Tv Stick. Mission Power Usb -Mission Cables Usb Power Cable Fire Tv Stick Fire Tv Included
    1. Works with new firetv sticks that require more power output. https://puqus.com/mission-cables-power-cable-included-8147319k943/#mission-cables-power-cable-included
    2. Highlight: Advanced Technology - Includes Special Power Management Circuitry That Enhances The Peak Power Capability Of The Usb Port By Storing Excess Energy And Then Releasing It As Needed.
    3. Highlight: Declutter Your Tv Area - Ideal Length For Conveniently Connecting Fire Tv Stick To The Tv's Side Usb/hdmi Ports.
    Half Price Mission Cables Usb Power Cable Fire Tv Stick Fire Tv Included (Consumer Electronics) Mc9g
  • Discover it
    Listed 2 Prong Samsung Monitor Console (Pwr+)

    Listed 2 Prong Samsung Monitor Console (Pwr+) 2055

    Read Review Listed 2 Prong Samsung Monitor Console (Pwr+), Ul Listed Extra Long 12 Ft 2-prong Ac Wall 2 Slot Power Cord L-type Samsung Led Lcd Tv Smart Monitor, Xbox One-s X, Ps4 Console Cable Figure 8 - 3903-000853 Pwr+: Powering Millions Of Laptops, Tablets And Electronic Gadgets And A Go-to Brand For Premium Replacement Chargers And Accessories Since 2007. Pwr+ Chargers Manufactured The Highest -Ul Listed Pwr+ Extra Long 12 Ft 2-prong Ac Wall 2 Slot Power Cord L-type Samsung Led Lcd Tv Smart Monitor, Xbox One-s X, Ps4 Console Cable Figure 8 - 3903-000853 3903-000599
    1. Special: Compatibility: Samsung Led Lcd Tv Smart Monitor, Xbox One S X, Ps4 Playstation 4 Console. Led Lcd Smart Tv, Monitor, Printer, Scanner, Game Console, Entertainment System, Audio Multiroom Speaker, Music System, Sound Bar, Retro Boombox, Action Keyboard, Digital Piano, Charging Dock, Wireless Backup, Wi-fi Base Station, Laptop Notebook Charger, Camera Battery Charger And Other Devices Requiring 2 Prong Ac Cord. Check Product Description.
    2. Order came quickly and the cord was just what we needed. Thank you! https://puqus.com/listed-2-prong-samsung-monitor-console-205505c5enla/#listed-2-prong-samsung-monitor-console
    3. Special: Samsung Led Lcd Tv Home Audio Theater Monitor Soundbar Sonos Playbar, Jbl Cinema Klipsch Reference R-20b Yamaha Sound Bar Yas-106, Yas-107bl, Yas-207bl Zvox Soundbase 570 ; Dell, Sony, Acer, Asus, Gateway, Toshiba, Msi, Compaq Laptop Charger And Etc.
    Most Wishlist Listed 2 Prong Samsung Monitor Console (Computer Add On) 866 Pwr53 78461

Product Image Gallery

Top-datacomm-50-3323-wh-kit-panel-organizer-solution-99001pb7uva-Content